masonry drill
Use in any rotary or percussion hammer drill with a Jacobs type chuck at any R.P.M. up to 1000. The harder the material, the greater the pressure, and the slower the speed. Standard C-2 carbide tip with 130° point and positive angle. ICS masonry drills are black surface treated or bright zinc plated.
CHOOSE MASONRY DRILL TYPE
MASONRY DRILLS - FAST SPIRAL
Masonry Drill - Black Finish page 142
Masonry Drill - Zinc Plated page 142
Carbide Tipped Fast Spiral Masonry Drill Bits are designed for rotary drilling into brick, cinder block, tile, plaster, and other brittle materials. Brittle materials will require slower speeds and light to moderate pressure as material is being ground, not broken. The fast spiral flute design creates less heat buildup when drilling. Has a special carbide tip with 130° point and positive angles for fast penetration. They can be used in any 3-jaw chuck rotary style drill.
Masonry Drill Sets - 4 pc - Fast Spiral - 4" Length page 142
1/4, 5/16, 3/8, 1/2
MASONRY DRILLS - WIDE SPIRAL
Masonry Drill - Wide Spiral - Carbide Tipped - Black Finish page 143
Masonry Drill - Wide Spiral - Carbide Tipped - Zinc Plated page 143
Carbide Tipped Wide Spiral Masonry Drill Bits are designed for rotary drilling into concrete, masonry, marble, stone and rock. The harder the material, the more pressure applied and the slower the speed as material is being ground up, not broken as a hammer drill would do. The wide spiral flute design is very strong and remove debris rapidly. Drills have a special carbide tip with a 130° point and positive angle for fast penetration. They can be used in any 3-Jaw chuck rotary style drill. They are also known as Carbide Tipped Slow Spiral Masonry Drill Bits.
Masonry Drill - Wide Spiral - Carbide Tipped - Metric page 144
Carbide Tipped Wide Spiral Metric Masonry Drill Bits are designed for rotary drilling into concrete, masonry, marble, stone and rock. The harder the material, the more pressure applied and the slower the speed as material is being ground up, not broken as a hammer drill would do. The wide spiral flute design is very strong and removes debris rapidly. Drills have a special carbide tip with a 130° point and positive angle for fast penetration. They can be used in any 3-Jaw chuck rotary style drill. ICS Carbide Tipped Metric Drills are true metric sizes (not fractional equivalents) for drilling pilot holes for European Anchors. They are also known as Carbide Tipped Slow Spiral Metric Masonry Drill Bits.
Masonry Drill Sets - 4 pc - Wide Spiral - 4" Length page 142
1/4, 5/16, 3/8, 1/2
MASONRY HAMMER DRILLS
FRACTIONAL
Masonry Hammer Drill - Heavy Duty - Wide Spiral - Black Finish page 145
Special C-8 carbide tip with negative tip angle and 130° point. Use in any percussion hammer drill. MDH masonry drills are black surface treated. Note: MDH drills have a negative tip angle and will drill about 10% slower if used for rotary drilling.
Masonry Hammer Drill - Straight Shank - Tang Shank Style page 146
Carbide Tipped Straight Shank Tapcon® Bits are designed for use in Tapcon®, Condrive®, and Black and Decker® drilling systems for setting masonry anchor screws with self-cutting threads. Straight shank Tapcon bits can be used in any drill with 3-jawed drill chuck. All ICS straight shank Tapcon bits meet or exceed all tolerances recommended by manufacturers of screw-type masonry anchors. They are also known as Screw-Type Anchor Bits or Concrete Screw Drill Bits.
Masonry Hammer Drill - 4 Slot (SDS) Hex Drive Shank page 146
Carbide Tipped SDS-Plus Tapcon Hex Drive Rotary Hammer Bits are designed for use in Tapcon®, Condrive®, and Black and Decker® drilling systems for setting masonry anchor screws with self-cutting threads. SDS-Plus Tapcon hex drive bits have a 5/16" hex directly below the shank which fits into driver sleeve for installation. All ICS SDS-Plus Tapcon hex drive rotary hammer bits meet or exceed all tolerances recommended by manufacturers of screw-type masonry anchors. They are also known as Carbide Tipped Screw-Type Anchor Bits or Carbide Tipped Concrete Screw Drill Bits.
Masonry Hammer Drill - 4 Slot (SDS) Shank page 147
Carbide Tipped Slot Drive System SDS Masonry Hammer Drills are designed for use with all rotary hammer that specify SDS-Plus shank hammer drills. SDS plus shank hammer bits have 4 U-shaped slots cut into the .393 diameter shank, 2 positive rotary drive slots and 2 ball retainer slots to ensure a positive fit between the bit and the bit holder on a SDS-Plus rotary hammer drill which makes possible the most power transmission to the cutting edge for high speed drilling of holes up to 1" in diameter in concrete, masonry and stone. They are also known as SDS-Plus Drill Bits.
Masonry Hammer Drill - 2 Slot Shank - 3/4" Diameter page 149
Special C-8 carbide tip with negative tip angle and 130° point. Made to withstand the shock and impact of the hardest hitting rotary hammer drills. Will quickly penetrate the toughest aggregate.
Masonry Hammer Drill - 4 Slot Shank - Magic Shank page 149
Use in Ramset Dinadrill 330 or any SDS style power drill. They fit all two and four slot drive systems. Special C-8 carbide tip with negative angle and 130° point.
Masonry Hammer Drill - 5 Slot Shank - SDS-MAX Shank - Single Cutter page 150
Special Impact Carbide Tip with negative angle and 130° point. Fits the old and new Hilti® hammer drills, plus the new SDS-MAX® hammer drill from Bosch®. Will quickly penetrate the toughest aggregate.
Masonry Hammer Drill - 5 Slot Shank - SDS-MAX Shank - Multi-Cutter page 151
Carbide Tipped SDS-MAX Heavy Duty Slot Drive Masonry Hammer Drills with 4 cross cutting edges are designed for use with large SDS-MAX drive rotary hammers. The 4 cross cutting edges pulverize the material to be drilled better and quicker than single edge hammer bits. SDS-MAX drive hammer bits have 5 U-shaped slots cut into the .708" diameter shank, 3 positive rotary drive slots, and 2 ball retainer slots to hold bit in rotary hammer. It is the toughest drill of its kind and is often used instead of a carbide tipped core drill for drilling large diameter holes in concrete, masonry and stone.
Masonry Hammer Drill - Spline Shank - Single Cutter page 152
Carbide Tipped Spline Shank Drive Masonry Hammer Drills with a single cutting edge are designed for use with spline-drive rotary hammers. Spline drive hammer bits have 12 splines cut into the 3/4" diameter shank to ensure a positive fit between the bit and the bit holder on a spline drive rotary hammer which makes possible the most power transmission to the cutting edge for high speed drilling of large diameter holes in concrete, masonry and stone.
Masonry Hammer Drill - Spline Shank - Multi Cutter page 153
Carbide Tipped Spline Shank Drive Masonry Hammer Drills with 4 cross cutting edges are designed for use with spline drive rotary hammers. The 4 cross cutting edges pulverize the material to be drilled better and quicker than single edge hammer bits. Spline drive hammer bits have 12 splines cut into the 3/4" diameter shank to ensure a positive fit between the bit and the bit holder on a spline drive rotary hammer which makes possible the most power transmission to the cutting edge for high speed drilling of large diameter holes in concrete, masonry and stone.
Masonry Hammer Drill - "A" Taper Shank page 154
Carbide Tipped "A" Taper Shank Masonry Hammer Bits are designed to fit into "A" taper chuck adapter which allow "A" taper shank masonry hammer bits to be used with almost any current or discontinued model hammer drill. They are manufactured with a taper of 1" in 20" and are intended for drilling holes from 3/16" to 7/8" in concrete, masonry and stone. They are also known as "A" Taper Shank Rotary Hammer Drill Bits.
Masonry Hammer Drill - "B" Taper Shank page 154
Carbide Tipped "B" Taper Shank Masonry Hammer Bits are designed to fit into "B" taper chuck adapter which allow "B" taper shank masonry hammer bits to be used with almost any current or discontinued model hammer drill. They are manufactured with a taper of 1" in 10" and are intended for drilling holes from 1/2" to 1-1/4" in concrete, masonry and stone. They are also known as "B" Taper Shank Rotary Hammer Drill Bits or "K" Taper Shank Rotary Hammer Drill Bits.
Masonry Hammer Drill - 7/16" Shank - Skil 726 - Hex Shank page 156
Carbide Tipped Heavy Duty 7/16" Hex Shank Masonry Hammer Drills, commonly classified as the Skil 726 Hex Shank, are designed to fit the following 7/16" hex drive rotary hammers:

Skil 726
Milwaukee 5300, 5305, 5310, 5314, 5315

Hex shank rotary hammer drills have 6 flats on the shank to ensure a positive drive action and a flat bottom on the end of the shank for tough hammering of aggregate. They are used for drilling holes from 7/16" to 1-1/2" in concrete, masonry and stone.
Masonry Hammer Drill - 9/16" Shank - Skil 728 - Hex Shank page 156
Carbide Tipped Heavy Duty 9/16" Hex Shank Masonry Hammer Drills, commonly classified as the Skil 726 Hex Shank, are designed to fit the following 9/16" hex drive rotary hammers:

Skil 628, 728, 731, 732, 1760
Black and Decker 5048
Rockwell 602, 1602, 606, 616
Milwaukee 5325-26
Miller Falls SP 499K

Hex shank rotary hammer drills have 6 flats on the shank to ensure a positive drive action and a flat bottom on the end of the shank for tough hammering of aggregate.
Masonry Hammer Drill - 3/8" Shank - Skil 706 - Hex Shank page 157
Carbide Tipped Heavy Duty 3/8" Hex Shank Masonry Hammer Drills, commonly classified as the Skil 706 Hex Shank, are designed to fit the following 3/8" hex drive rotary hammers:

Skil 706, 707, 708, 1706, 511
Black and Decker 5040, 5049
Milwaukee M06
Ramset 620
Rockwell 600, 601

Hex shank rotary hammer drills have 6 flats on the shank to ensure a positive drive action and a flat bottom on the end of the shank for tough hammering of aggregate.
Masonry Hammer Drill - 7/16" Shank - Skil 717 - Hex Shank page 157
Carbide Tipped Heavy Duty 7/16" Hex Shank Masonry Hammer Drills, commonly classified as the Skil 717 Hex Shank, are designed to fit the following 7/16" hex drive rotary hammers:

Skil 717, 718, 719, 1750
Black and Decker 717, 718, 719, 5045, 5046, 5050

Hex shank rotary hammer drills have 6 flats on the shank to ensure a positive drive action and a flat bottom on the end of the shank for tough hammering of aggregate. They are used for drilling holes from 7/16" to 1-1/2" in concrete, masonry and stone.
Masonry Hammer Drill - 9/16" Shank - Phillips 747 - Hex Shank page 158
Carbide Tipped Heavy Duty 9/16" Hex Shank Masonry Drills, commonly classified as the Phillips 747 Hex Shank, are designed to fit the following 9/16" hex drive rotary hammers.

Phillips 747-39, 700
Bosch 11201
Metabo RH 65, 90, 90x

Hex shank rotary hammer drills have 6 flats on the shank to ensure a positive drive action and a flat bottom on the end of the shank for tough hammering of aggregate. They are used for drilling holes from 7/16" to 1-1/2" in concrete, masonry and stone.
Masonry Hammer Drill - 3/4" Shank - Skil 736 - Hex Shank page 158
Carbide Tipped Heavy Duty 3/4" Hex Shank Masonry Drills, commonly classified as the Skil 736 Hex Shank, are designed to fit the following 3/4" hex drive rotary hammers.

Skil 736, 1770
Stanley HD20, 45

Hex shank rotary hammer drills have 6 flats on the shank to ensure a positive drive action and a flat bottom on the end of the shank for tough hammering of aggregate. They are used for drilling holes from 3/4" to 2" in concrete, masonry and stone.

METRIC
Masonry Hammer Drill - 21.0mm Shank - Kango 950 - Hex Shank page 159
Carbide Tipped Heavy Duty 21.00mm Hex Shank Masonry Drills, commonly classified as the Kango 950 Hex Shank, are designed to fit the following 21.00mm hex drive rotary hammers.

Kango 950, 900, 1400, 450x, 950x
Hitachi DH5OSA, H55SA
Makita HR5000R/K, HM1200K
Ryobi CH485PK

Hex shank rotary hammer drills have 6 flats on the shank to ensure a positive drive action and a flat bottom on the end of the shank for tough hammering of aggregate.
Masonry Hammer Drill - 19.0mm Shank - Kango 637 - Hex Shank page 159
Carbide Tipped Heavy Duty 19.00mm Hex Shank Masonry Drills, commonly classified as the Kango 637 Hex Shank, are designed to fit the following 19.00mm hex drive rotary hammers.

Kango 500, 501, 625, 627, 637, 750, 750x
Rockwell 605, 607, 637, 750, 750x, 60

Hex shank rotary hammer drills have 6 flats on the shank to ensure a positive drive action and a flat bottom on the end of the shank for tough hammering of aggregate.

SETS
Masonry Hammer Drill Sets - SDS Shank page 147
1 each: 3/16x4, 1/4x4
2 each: 1/4x6
1 each: 5/16x6, 3/8x6, 1/2x6
Masonry Hammer Drill Sets - Ramset Shank page 147
1 each: 3/16x4, 1/4x4
2 each: 1/4x6
1 each: 5/16x6, 3/8x6, 1/2x6
MASONRY DRILL - PERCUSSION CORE
Masonry Percussion Core Drill page 141
Special C-8 Carbide Tipped Percussion Core Bits are designed to drill large diameter holes with most rotary hammer drills. Carbide Tips can withstand continuous hammering action and give maximum drilling time.
Core Bits For Thin Wall Core Drills page 141
Shanks For Percussion Core Drills page 141
Masonry Drill - Percussion Core Pilot Drill page 141
Use a pilot drill for a more accurate starting position and to keep the drill from walking. The pilot drill is used only to start the initial starting groove and is then removed before drilling is continued.
Masonry Drill Ejector Key page 141
Use Ejector Key to push Pilot drill out of Tapered Core Body.
MASONRY DRILL - ROTARY CORE
Masonry Drill - Solid Body Style page 139
Multi-tipped core bits are designed to drill large diameter holes and to handle difficult rotary drilling problems. Carbide tips cut only the rim of a hole leaving the core intact. For rotary drilling only.
Masonry Drill - Rotary Core Pilot Drill page 139
Use a pilot drill for a more accurate starting position and to keep the drill from walking. The pilot drill is used only to start the initial starting groove and is then removed before drilling is continued.
Masonry Drill - Rotary Core Shanks page 139
MASONRY DRILL - (THIN WALL) CORE
Masonry (Thin Wall) Core Drills page 140
Special Carbide Tipped Thin Wall Percussion Core Bits are designed to drill large diameter holes with most rotary hammer drills. Carbide Tips can withstand continuous hammering action and give maximum drilling life.

Core Bits For Thin Wall Core Drills page 140
Shanks For Thin Wall Core Drills page 140
Masonry Drill - Thin Wall Core Pilot Drill page 140
Use a pilot drill for a more accurate starting position and to keep the drill from walking. The pilot drill is used only to start the initial starting groove and is then removed before drilling is continued.
MASONRY DRILL - (WET DRILLING) DIAMOND CORE
Masonry Drill - Wet Drilling Diamond Core - Premium Grade page 139
Wet Drilling Diamond Core Drills are used for cutting miscellaneous types of concrete, masonry, and stone. They are made to cool from the center and should be used in either vacuum or magnetic based diamond drilling machines. Use either water or cutting oil for lubrication and cooling. Do not use dry or use in a hammer drill.
CARPET STUBBY DRILLS
Carpet Stubby Drills - Carbide Tipped page 144
Carbide Tipped Carpet Stubby Drills are designed specially for easy installation of carpets. They are used to drill holes in concrete or terrazzo flooring for tack stripping.
GLASS CUTTING DRILLS
Glass Cutting Drills - Carbide Tipped page 168
Carbide Tipped Glass Drills are designed for drilling glass, mirror glass, tile, ceramics, and porcelain. Special spear point allows a precise hole to start without walking and can also be used to drill a hole smaller than drill diameter.
UNIVERSAL DRILLS
Universal Drills - Carbide Tipped page 136
Carbide Tipped Universal Drills are designed with a diamond ground special drill point for multi-purpose drilling. It is highly effective for drilling hard metals and alloys, reinforced concrete, stone, tile, ceramics, marble, granite, glass, hard and soft woods, plastics and many other difficult materials. Often used to drill out broken taps and hardened bolts. They are also known as Carbide Tipped Multi-Purpose Drills or Carbide Tipped Utility Drills.
Carbide Tipped Universal Drill - Set page 136
7 Piece Drill Set
YANKEE PUSH DRILLS
Yankee Push Drills - Carbide Tipped page 144
Carbide Tipped Yankee Push Drills are designed to fit Yankee Push Drill systems where 3/16" and 1/4" anchor holes are required. They are ideal for drywall and concrete block.
ADAPTERS
SDS Shank Quick Release Adapters page 148
SDS Shank adapters allow you to use 2 slot and 4 slot shank masonry drills with different models of electric hammer drills. Each shank configuration will fit the hammer drill model No.'s listed.
Taper Chuck Adapters page 155
Taper Chuck adapters allow you to use: "A" or "B" taper shank masonry bits with almost any make of electric hammer drill. Each shank configuration will fit the hammer drill model no.'s listed. A draft pin is included with each adapter.